Research Progress of Metal Semi-solid Forming Technology
DOI:
https://doi.org/10.54691/n7249052Keywords:
Semi-solid; Forming Technology; Research Development.Abstract
This article summarizes the application of semi -solid forming technology in non -ferrous metal materials and steel.This paper is to expound the historical evolution of metal semi-solid forming technology, the classification of semi-solid forming technology, and the preparation process of semi-solid metal billet slurry. It is to summarize the domestic and foreign research progress of metal semi-solid forming, discussing the existing problems in the development of metal semi-solid forming likewise the future challenges and opportunities.
Downloads
References
[1] D.B. Spencer, R. Mehrabian, M.C. Flemings. Rheological behavior of Sn-15 pct Pb in the crystallization range[J]. Metallurgical Transactions, 1972, 7:1925-1932.
[2] M.C. Flemings. Behavior of metal alloys in the semisolid state [J]. Metallurgical Transactions A, 1991, 22A:957-981.
[3] Luo Shoujing, Tian Wentong, Xie Shuisheng, Mao Weimin. Semi-solid processing technology and application[J]. Chinese colored genus Acta Sinica, 2000, 10(6): 765-773.
[4] XIE Shuisheng. Development and application of metal semi-solid processing technology[J]. Chinese Journal of Plasticity Engineering, 2002,9(2):1-11.
[5] JIANG Peng, HE Xiaomao. Process Overview of Semi-Solid Forming and Selection of Mold Materials[J]. Mould Technology, 1998,2: 54-60.
[6] LIU Guojun et al. Study on Semi-solid Forming Process of Several Automotive Aluminum Alloys[J]. Special Casting & Nonferrous Metals, 2001, S1:7-9.
[7] Wen-zhi ZHU, Wei-min MAO, Qin TU. Preparation of semi-solid 707 aluminum alloy slurry by serpentine pouring channel [J]. Trans. Nonferrous Met.Soc. China 2014,24: 954-960.
[8] Wang Weiwei, Han Fei, Song Liang, Luo Shoujing. Research on Semi-solid Forging Forming Technology of Aluminum Alloy Impeller[J]. Special Casting & Nonferrous Alloys, 2012, 32(5): 426-429.
[9] JIANG Jufu. Preparation of AZ91D semi-solid blanks by the new SIMA method and its thixotropic die forging[D]. Harbin: Ph.D. dissertation, Harbin Institute of Technology, 2005.
[10] Zhang Fan, Xu Jun, Zhang Zhifeng, et al. A356 Numerical simulation of aluminum alloy wheel Yi semi-solid extrusion casting[J].Special Casting & Nonferrous Metals, 2012, 32(5): 422-425.
[11] YOUNG.K.P, RIEK.R.G, FLEMINGS.M.C. Structure and properties of thixocast steels [J]. Metals Technology, 1979, 6: 130-137.
[12] Mao Weimin, Zhao Aimin et al. Preparation and Rolling of 1Cr18Ni9Ti Stainless Steel Semi-Solid Slurry[J]. Acta Metallurgica Sinica, 2003, 39(10): 1071-1075.
[13] K.P. SOLEK, A.RASSILI, J.C. PIERRET et al. Characterization of thixoforming process of 100Cr6 steel[C]. Proceedings of the 11th International Conference on Semi-Solid Processing of Alloys and Composites, Beijing: Elsevier Ltd, 2010: 1037-1041.
[14] L.KHIZHNYAKOVA, M.EWERING, G.HIRT et al. Metal flow and die wear in semi-solid forging of steel using coated dies[C]. Proceedings of the 11thInternational Conference on Semi-Solid Processing of Alloys and Composites. Beijing: Elsevier Ltd, 2010:954-960.
[15] Song Renbo, Wang Changsheng, Kang Yonglin, et al. Rheological stress and microstructure of semi-solid 60Si2Mn[J]. Journal of Beijing University of Science and Technology,2009,31(3): 335-340.
[16] Song Renbo, Kang Yonglin, Sun Jianlin, et al. Experimental test of rheological rolling of semi-solid iron and steel materials[J]. Journal of University of Science and Technology Beijing, 2001, 23 (5):439-441.
[17] Kang Yonglin,Song Renbo,Dong Hongbo,Ren Xueping. Finite element simulation of 60Si2Mn semi-solid rolling[J]. Journal of Mechanical Engineering,2002,38(6):83-87.
[18] M.BUNCK, E.SUBASIC, A.BUHRIG-POLACZEK et al. Thixo-casting combination spanners using stainless steel X39CrM017[C]. Proceedings of the 11th International Conference on Semi-Solid Processing of Alloys and Composites, Beijing: Elsevier Ltd, 2010:998-1 004.
[19] L.ROGAL, J.DUTKIEWICZ, T.CZEPPE et al.Characteristics of 100Cr6 bearing steel after thixo-forming process performed with prototype device[J]. Trans. Nonferrous Met. Soc. China, 2010, 20: 1033-1036.
[20] B.MASEK, D.AISMAN, M.BEHULOVA, et al. Structure of miniature components from steel produced by forming in semi-solid state [C]. Proceedings of the 11 th International Conference on Semi-Solid Processing of Alloys and Composites.Beijing: Elsevier Ltd, 2010:l037-1041.
[21] YANG Maosheng,LI Shiqi,ZHONG Xueyou,MAO Weimin. Experimental study on the preparation of semi-solid billets of 60Si2Mn spring steel[J]. Journal of Materials Science and Technology, 2005, 13(3): 268-271.
[22] ZHANG Lizhong, LI Haikai, HU Yuanmeng, et al. JOURNAL OF BEIJING JIAOTONG UNIVERSITY,2006, 30(4): 77-81.
[23] Guan Renguo, Li Gang, Li Junpeng, et al. Preparation of 1Crl8Ni9Ti stainless steel semi-solid materials by inclined shear cooling[J].Journal of Northeastern University:Natural Science, 2005, 26 (9): 867-870.
[24] LI Jiguan, KANG Yonglin, SONG Renbo, et al. Evolution of partial remelted microstructure of semi-solid T12 steel[J].Metal Heat Treatment,2010,35(3) :47-50.
[25] ZHOU Rongfeng,YANG Chengdong,JIANG Yehua,ZHOU Rong. Effect of inclined plate length on semi-solid microstructure of supereutectic high chromium cast iron[J].Special Casting & Nonferrous Alloys,2008,28(2):125-127.
[26] Łukasz Rogal, Grzegorz Korpala , Jan Dutkiewicz. Evolution of microstructure in 100Cr6 steel after cooling from a thixoforming temperature to bainitic transformation ranges[J]. Materials Science& Engineering A, 2015,624:291–299.
[27] HE Shuhua,ZHANG Lizhong,JIAO Zhongsheng,LIU Jinxiang,CHEN Yu,LIU Wen,XING Shuming. Failure and material selection of semi-solid metal rheological forming mold[J].Special Casting & Nonferrous Alloys,2004(2): 33-35.
[28] YAO Shuqing. Research on special coatings for extrusion casting of iron and steel materials[D]. Beijing:Ph.D. dissertation, Beijing Jiaotong University, 2010.
[29] Feng Junjie,Li Yaojun. Research on Improving the Life of 3Cr2W8V Steel Hot Mold[J]. Mechanical Technology, 2005(3):43-45.
[30] Kim.S.K, Kim.K.D, Kim.Y.J. Development of SRT Technology[C]. Proceeding of the 7th S2P,Tsukuba, JAPAN, National Institute of Advanced Industrial Science and Technology, Japan Society for Technology of Plasticity, Sept.23 -29,2002:391-396.
[31] Lugscheider. E, Bobzin. K. Development, Investigation and Characterization of New Surface Technologies for the Use of Semisolid Metal Forming of Steel[C]. Proceeding of the 7thS2P, Tsukuba, JAPAN, National Institute of Advanced Industrial Science and Technology, Japan Society for Technology of Plasticity, Sept.23 -29,2002:385-390.
[32] S.I. Borovik, T.N. Ivanova, N.L. Mironenko et al. Protective coating as a means of improving heat resistance of the refractory lining for extra-furnace steelmaking facilities[J]. Refractories and Industrial Ceramies,2005,46(1):24-26.
[33] J. Lin, S. Carrera, A.O. Kunrath, D. Zhong et al. Design Methodology for Optimized Die Coatings: The case for aluminum Pressure die-casting[J]. Surface and Coatings Technology, 2006,201(6,4):2930-2941.
[34] Xu Binshi, Zhu Shaohua, et al. Theory and technology of surface engineering[M].Beijing:National Defense Industry Press,1999.
[35] Zhou Yichun, Liu Qixing, Yang Li et al. Failure Mechanism and Life Prediction of Thermal Barrier Coatings[J]. Solid Mechanics Newspaper, 2010, 31(5):504-531.
[36] M.Matsumoto, N.Yamaguchi, H.Matsubara. Low Thermal Conductivity and High Temperature Stability of ZrO2-Y2O3-La2O3 Coatings Produced by Electron Beam PVD [J] . Scripta Materialia, 2004, 50: 867-871.
[37] R.Vassen, F.Traeger, D.Stover. New Thermal Barrier Coatings Based on Pyrochlore/YSZ Double-Layer Systems [J]. International Journal of Applied Ceramic Technology, 2004, 1: 351-361.
[38] R.A.MILLER. Thermal barrier coatings for aircraft engines: History and directions [J]. Journal of Thermal Spray Technology, 1997, 6(1):35-42.
[39] Guo Hongbo,Gong Shengkai,Xu Huibin. Research progress on new high-temperature/ultra-high-temperature thermal barrier coating and preparation technology[J].Acta Aeronautical Sinica, 2014, 35: 1-10.
[40] MU Rende,SONG Xiwen,TAO Chunhu,HE Limin. Test Method of Thermal Diffusivity of EB-PVD Thermal Barrier Coatings and Its Influencing Factors[J]. Journal of Central South University(Natural Science Edition), 2009, 39(2): 256-261.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
